Z31/SENSORS/cas php - Revision history

CleanupBot: Rewrite 5 dev.z31library.com link(s) to z31library.com

2026-10-20T22:53:20Z

Rewrite 5 dev.z31library.com link(s) to z31library.com

← Older revision		Revision as of 22:53, 20 October 2026
Line 1:		Line 1:
	{{ImportedFrom\|site=Xenonzcar\|title=Z31 Crank Angle Sensor\|url=https://~~dev.~~z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|archive=https://~~dev.~~z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|fetched=2026-05-15}}		{{ImportedFrom\|site=Xenonzcar\|title=Z31 Crank Angle Sensor\|url=https://z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|archive=https://z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|fetched=2026-05-15}}

	== Z31 Crank Angle Sensor ==		== Z31 Crank Angle Sensor ==

	https://~~dev.~~z31library.com/xenonzcar_archive/z31/images/Sensors/CASCrankanglesensor.jpg		https://z31library.com/xenonzcar_archive/z31/images/Sensors/CASCrankanglesensor.jpg

	=== Crank Angle Sensor (CAS) ===		=== Crank Angle Sensor (CAS) ===
Line 19:		Line 19:
	Below you will see the pinout of the Crank Angle Sensor. Click on each pin area for details.		Below you will see the pinout of the Crank Angle Sensor. Click on each pin area for details.

	https://~~dev.~~z31library.com/xenonzcar_archive/z31/images/Sensors/4prongplug.jpg		https://z31library.com/xenonzcar_archive/z31/images/Sensors/4prongplug.jpg

	=== Common Problems ===		=== Common Problems ===
Line 176:		Line 176:
	=== Sources Used ===		=== Sources Used ===

	* [https://~~dev.~~z31library.com/xenonzcar_archive/z31/z31fsm.php 1984-1988 Nissan 300ZX Factory Service Manual]		* [https://z31library.com/xenonzcar_archive/z31/z31fsm.php 1984-1988 Nissan 300ZX Factory Service Manual]

	[[Category:Imported from Xenonzcar]]		[[Category:Imported from Xenonzcar]]

CleanupBot: Restore Sources Used dropped by import (verbatim from archive)

2026-10-20T22:13:44Z

Restore Sources Used dropped by import (verbatim from archive)

← Older revision		Revision as of 22:13, 20 October 2026
Line 173:		Line 173:
	\| (1987 - 1991)		\| (1987 - 1991)
	\|}		\|}

			=== Sources Used ===

			* [https://dev.z31library.com/xenonzcar_archive/z31/z31fsm.php 1984-1988 Nissan 300ZX Factory Service Manual]

	[[Category:Imported from Xenonzcar]]		[[Category:Imported from Xenonzcar]]

CleanupBot: Rebuild 1 table(s) as wikitable from archived source; fix column alignment

2026-10-20T22:08:15Z

Rebuild 1 table(s) as wikitable from archived source; fix column alignment

@@ Line 56: / Line 56: @@
 ==== Vehicles Using the Same Crank Angle Sensor (CAS) as the Z31 ====
-| Make | Model | Years |
+{| class="wikitable"
-|---|---|---|
+! Make
-| INFINITI | G20 | (1991 - 1994) |
+! Model
-| INFINITI | M30 | (1990 - 1992) |
+! Years
-| ISUZU | TROOPER | (1988 - 1991) |
+|-
-| MERCURY | VILLAGER | (1993 - 1998) |
+| INFINITI
-| NISSAN | 200SX | (1984 - 1987) |
+| G20
-| NISSAN | 240SX | (1989 - 1990) |
+| (1991 - 1994)
-| NISSAN | 280ZX | (1981 - 1983) |
+|-
-| NISSAN | 300ZX | (1984 - 1989) |
+| INFINITI
-| NISSAN | 720 PICKUP | 1986 |
+| M30
-| NISSAN | AXXESS | (1990 - 1995) |
+| (1990 - 1992)
-| NISSAN | D21 PICKUP | (1986 - 1994) |
+|-
-| NISSAN | MAXIMA | (1985 - 1994) |
+| ISUZU
-| NISSAN | MULTI | (1986 - 1988) |
+| TROOPER
-| NISSAN | NX | (1992 - 1993) |
+| (1988 - 1991)
-| NISSAN | PATHFINDER | (1987 - 1995) |
+|-
-| NISSAN | PICKUP | 1995 |
+| MERCURY
-| NISSAN | PULSAR NX | (1983 - 1986) |
+| VILLAGER
-| NISSAN | QUEST | (1993 - 1998) |
+| (1993 - 1998)
-| NISSAN | SENTRA | (1984 - 1994) |
+|-
-| NISSAN | STANZA | (1986 - 1992) |
+| NISSAN
-| NISSAN | VAN | (1987 - 1988) |
+| 200SX
-| SUBARU | DL | (1987 - 1989) |
+| (1984 - 1987)
-| SUBARU | GL | (1987 - 1989) |
+|-
-| SUBARU | GL-10 | (1987 - 1989) |
+| NISSAN
-| SUBARU | LOYALE | (1990 - 1994) |
+| 240SX
-| SUBARU | RX | (1987 - 1989) |
+| (1989 - 1990)
-| SUBARU | STANDARD | 1987 |
+|-
-| SUBARU | XT | (1987 - 1991) |
+| NISSAN
 [[Category:Imported from Xenonzcar]]

XenonzcarImporter: Rewrite 2 archive URL(s) to internal wikilinks

2026-05-17T01:59:27Z

Rewrite 2 archive URL(s) to internal wikilinks

← Older revision		Revision as of 01:59, 17 May 2026
Line 28:		Line 28:
	=== Troubleshooting ===		=== Troubleshooting ===

	The ECCS of the Z31 will flash trouble codes using two LED lamps on the ECU. [~~https://dev.z31library.com/xenonzcar_archive/z31~~/computerpinout~~.html~~ A chart of these codes is available on the ECU page].		The ECCS of the Z31 will flash trouble codes using two LED lamps on the ECU. [[Z31/computerpinout\|A chart of these codes is available on the ECU page]].

	'''Code 11:'''Indicates a fault in the Crank Angle Sensor Circuit.		'''Code 11:'''Indicates a fault in the Crank Angle Sensor Circuit.
Line 39:		Line 39:

	-		-
	'''Check harness continuity:'''If steps 1 and 2 are good, disconnect the 20-pin connector at the[~~https://dev.z31library.com/xenonzcar_archive/z31~~/computerpinout~~.html~~ ECCS unit]and check resistance between'''Pins 8 and 17'''. This ensures no broken insulation or open circuit in the harness.		'''Check harness continuity:'''If steps 1 and 2 are good, disconnect the 20-pin connector at the[[Z31/computerpinout\|ECCS unit]]and check resistance between'''Pins 8 and 17'''. This ensures no broken insulation or open circuit in the harness.

	-		-

XenonzcarImporter: Inline image refs: rewrite to local archive; clean empty image artifacts

2026-05-16T18:01:27Z

Inline image refs: rewrite to local archive; clean empty image artifacts

← Older revision		Revision as of 18:01, 16 May 2026
Line 1:		Line 1:
	{{ImportedFrom\|site=Xenonzcar\|title=Z31 Crank Angle Sensor\|url=~~http~~://~~www~~.~~xenonzcar~~.com/z31/SENSORS/cas.php.html\|archive=https://dev.z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|fetched=2026-05-15}}		{{ImportedFrom\|site=Xenonzcar\|title=Z31 Crank Angle Sensor\|url=https://dev.z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|archive=https://dev.z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html\|fetched=2026-05-15}}

	== Z31 Crank Angle Sensor ==		== Z31 Crank Angle Sensor ==

	~~[http~~://~~www~~.~~xenonzcar~~.com/z31/images/Sensors/CASCrankanglesensor.jpg ~~image: Crank Angle Sensor]~~		https://dev.z31library.com/xenonzcar_archive/z31/images/Sensors/CASCrankanglesensor.jpg

	=== Crank Angle Sensor (CAS) ===		=== Crank Angle Sensor (CAS) ===
Line 19:		Line 19:
	Below you will see the pinout of the Crank Angle Sensor. Click on each pin area for details.		Below you will see the pinout of the Crank Angle Sensor. Click on each pin area for details.

	~~[http~~://~~www~~.~~xenonzcar~~.com/z31/images/Sensors/4prongplug.jpg ~~image: Crank Angle Sensor Plug]~~		https://dev.z31library.com/xenonzcar_archive/z31/images/Sensors/4prongplug.jpg

	=== Common Problems ===		=== Common Problems ===
Line 28:		Line 28:
	=== Troubleshooting ===		=== Troubleshooting ===

	The ECCS of the Z31 will flash trouble codes using two LED lamps on the ECU. [~~http~~://~~www~~.~~xenonzcar~~.com/z31/computerpinout.html A chart of these codes is available on the ECU page].		The ECCS of the Z31 will flash trouble codes using two LED lamps on the ECU. [https://dev.z31library.com/xenonzcar_archive/z31/computerpinout.html A chart of these codes is available on the ECU page].

	'''Code 11:'''Indicates a fault in the Crank Angle Sensor Circuit.		'''Code 11:'''Indicates a fault in the Crank Angle Sensor Circuit.
Line 39:		Line 39:

	-		-
	'''Check harness continuity:'''If steps 1 and 2 are good, disconnect the 20-pin connector at the[~~http~~://~~www~~.~~xenonzcar~~.com/z31/computerpinout.html ECCS unit]and check resistance between'''Pins 8 and 17'''. This ensures no broken insulation or open circuit in the harness.		'''Check harness continuity:'''If steps 1 and 2 are good, disconnect the 20-pin connector at the[https://dev.z31library.com/xenonzcar_archive/z31/computerpinout.html ECCS unit]and check resistance between'''Pins 8 and 17'''. This ensures no broken insulation or open circuit in the harness.

	-		-

XenonzcarImporter: XenonzcarImporter moved page Sites/Xenonzcar/z31/SENSORS/cas php to Z31/SENSORS/cas php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

2026-05-16T06:38:39Z

XenonzcarImporter moved page Sites/Xenonzcar/z31/SENSORS/cas php to Z31/SENSORS/cas php without leaving a redirect: Flatten Sites/ namespace; provenance preserved via ImportedFrom banner

← Older revision	Revision as of 06:38, 16 May 2026
(No difference)

XenonzcarImporter: Site import

2026-05-16T06:27:11Z

Site import

New page

{{ImportedFrom|site=Xenonzcar|title=Z31 Crank Angle Sensor|url=http://www.xenonzcar.com/z31/SENSORS/cas.php.html|archive=https://dev.z31library.com/xenonzcar_archive/z31/SENSORS/cas.php.html|fetched=2026-05-15}}

== Z31 Crank Angle Sensor ==

[http://www.xenonzcar.com/z31/images/Sensors/CASCrankanglesensor.jpg image: Crank Angle Sensor]

=== Crank Angle Sensor (CAS) ===

The crank angle sensor is a basic signal sensor for the entire ECCS. It monitors engine speed and piston position, sending signals to the ECCS control unit to control fuel injection, ignition timing, idle speed, fuel pump operation, and EGR operation.

The crank angle sensor contains a rotor plate and a wave form circuit. The rotor plate has '''360 slits''' for the 1° signal (engine speed signal) and '''six slits''' for the 120° signal (crank angle signal). Built-in LEDs and photo diodes within the wave forming circuit generate signals as the slits pass between them.

When the signal plate passes through the space between the LED and photo diode, each slit alternately cuts the light. This interruption creates an alternating voltage, which is then converted to an on-off pulse by the wave forming circuit. The signal is sent to the control unit via the green wire with yellow trace, which connects to pin 8 on the ECCS.

''WARNING'' - Do this modification at your own risk. We Are not responsable for any issues of your own doing.

=== Sensor Pinout ===

Below you will see the pinout of the Crank Angle Sensor. Click on each pin area for details.

[http://www.xenonzcar.com/z31/images/Sensors/4prongplug.jpg image: Crank Angle Sensor Plug]

=== Common Problems ===

* No Spark
* No Fuel From the Injectors but Fuel at the rail

=== Troubleshooting ===

The ECCS of the Z31 will flash trouble codes using two LED lamps on the ECU. [http://www.xenonzcar.com/z31/computerpinout.html A chart of these codes is available on the ECU page].

'''Code 11:'''Indicates a fault in the Crank Angle Sensor Circuit.

-
'''Check ground at Pin 4:'''Disconnect the 4-pin crank angle sensor connector at the sensor. Measure resistance to ground on'''Pin 4'''. It should read'''0 Ω'''. If not, you have a bad ground—repair or replace the harness.

-
'''Check voltage at Pin 1:'''With the ignition ON, use a multimeter to check for battery voltage on'''Pin 1'''of the connector.

-
'''Check harness continuity:'''If steps 1 and 2 are good, disconnect the 20-pin connector at the[http://www.xenonzcar.com/z31/computerpinout.html ECCS unit]and check resistance between'''Pins 8 and 17'''. This ensures no broken insulation or open circuit in the harness.

-
'''Final continuity test:'''Add a jumper wire between'''Pins 2 and 3'''of the Crank Angle Sensor plug. Then, test for continuity (should be 0 Ω) between'''Pins 8 and 17'''on the 20-pin connector at the ECCS unit.

If any of these tests fail, repair the harness or replace the faulty sensor as needed.

=== Replacement ===

The video below will guide you through the steps for replacing the Crank Angle Sensor. You can even use a newer 1990s S13 240SX Crank Angle Sensor unit.

[https://www.youtube.com/channel/UCiNZaOd8rmZuCSrDkgjRp8g YouTube channel]for this and many other informational videos.

=== Interchange ===

==== Vehicles Using the Same Crank Angle Sensor (CAS) as the Z31 ====

| Make | Model | Years |
|---|---|---|
| INFINITI | G20 | (1991 - 1994) |
| INFINITI | M30 | (1990 - 1992) |
| ISUZU | TROOPER | (1988 - 1991) |
| MERCURY | VILLAGER | (1993 - 1998) |
| NISSAN | 200SX | (1984 - 1987) |
| NISSAN | 240SX | (1989 - 1990) |
| NISSAN | 280ZX | (1981 - 1983) |
| NISSAN | 300ZX | (1984 - 1989) |
| NISSAN | 720 PICKUP | 1986 |
| NISSAN | AXXESS | (1990 - 1995) |
| NISSAN | D21 PICKUP | (1986 - 1994) |
| NISSAN | MAXIMA | (1985 - 1994) |
| NISSAN | MULTI | (1986 - 1988) |
| NISSAN | NX | (1992 - 1993) |
| NISSAN | PATHFINDER | (1987 - 1995) |
| NISSAN | PICKUP | 1995 |
| NISSAN | PULSAR NX | (1983 - 1986) |
| NISSAN | QUEST | (1993 - 1998) |
| NISSAN | SENTRA | (1984 - 1994) |
| NISSAN | STANZA | (1986 - 1992) |
| NISSAN | VAN | (1987 - 1988) |
| SUBARU | DL | (1987 - 1989) |
| SUBARU | GL | (1987 - 1989) |
| SUBARU | GL-10 | (1987 - 1989) |
| SUBARU | LOYALE | (1990 - 1994) |
| SUBARU | RX | (1987 - 1989) |
| SUBARU | STANDARD | 1987 |
| SUBARU | XT | (1987 - 1991) |

[[Category:Imported from Xenonzcar]]